Our Frame Grabber card has been optimized to allow high speed acquisition of full resolution images (up to 768 x 576 pixels) from multiple cameras. A short switching time between up to 4 cameras. Intertraff Frame Grabber card can acquire images from un-synchronized cameras with a very short switching time. The switching time is <33 ms in NTSC and <40 ms in PAL, Camera 1 camera 2 cameras 3 cameras 4 cameras.

Typical Switching Rate
25 fps
8 fps/cam
5 fps/cam
4 fps/cam

Four BNC connectors
Intertraff Frame Grabber is fitted with four BNC connectors providing the connection of up to four cameras with composite video output.

Ten digital TTL I/O lines
The I/O connector on the PCB is a 16-pin header connector, providing 10 general purpose I/O lines. These 10 TTL compatible input / output lines may be used for triggering image acquisition, lighting and alarm control. They are protected against overloads and electrostatic discharges.

Physical information
Format:
PCI board;
Size:
130 x 100;
Typical power consumption:
2.3 W
(350 mA @ +5V)
(10 mA @ +12V)
(30 mA @ - 12V)

Digital Input
Input channels: 8
Photo-coupler: PC-814
Input current: 10 mA rated 60 mA max for isolated input
Input Voltage: Up-to 24 VDC or 24V AC 50-1,000Hz)
Threshold Voltage: 2.4 VDC
Input impedance: 1.2 KW
Input mode: Isolation AC-filter/ Non-AC-filter
Isolated voltage: 5,000 Vrms channel-to-system

Relay Output
Output channels: 8
Relay type: 4 SPDT (Form C) 4 SPST (Form A)
Contact rating: 120V AC/DC, 0.5 A 24V DC, 1A
Breakdown voltage: 1000 V AC/DC min.
Release time: 8 msec typical
Operate time: 8 msec typical
Contact resistance: Bifurcated
Insulation resistance: 100M W min.
Life expectancy: >10 million operations at full load
LED indicators: Monitor ON/OFF status of each relay
Coil Voltage: +5V, 33 mA for each relay, total 0.264 A
Power supply of Relay: + 5V from the PCI-Bus

General Specifications
Dimension: 162 mm x 107 mm
Bus: 32-bit PCI bus
Operating temperature: 0 ~ 60°C (Operating);
Storage temperature: -20°C ~ 80°C (Operating);
Humidity: 5 to 90% non-condensing

Power Consumption
Power Consumption Note: No relay is energized
- +5V @ 140 mA

WALZcam™ Camera Specification

CCD Image Sensor: 1/2" B&W

Number of Pixels: EIA: 811 (H) X 508(V)

CCIR: 795(H) X 596(V)

Lens Mount: "CS" Mount

Resolution: >570 TV Lines

Sync System: Internal

Scanning System: 2:1 Interlaced

S/N Ratio: >46db

Backlight Compensation: ON/OFF

Video Output: 1 V P-P 75 OHMS (Unbalanced)

Shutter: 1/60 - 1/10,000

Gamma Characteristic: 0.50 -1 Selectable

AGC: ON/OFF- High/Low

Power Supply: DC 12V

Operating Temperature: -10°C - +40°C

Weight: Approx 50g

Housing/frame: In die-cast aluminium with wide cooling fins.

Diffuser: Tempered glass, 5 mm thick, thermal shock and impact resistant. (UNI7142 tests, British standard 3193).

Painting: With polyester powder, black or sand blasted silver, upon phosphochromate treatment, resistant to corrosive and saline environments.

Electric gear: 230V/50Hz power supply. Silicone flexible wire terminated with quick-connect clamps in admiralty brass, with fiberglass braid, 1 sqmm cross section. Polycarbonate 2P + T terminal block with maximum allowed lead cross section of 2.5 sqmm.

Equipment: Gasket in environment-friendly material. Cable gland in f.g. nylon, 1/2 gas thread. Gear box in f.g. nylon. The hinge-opening frame stays hooked to the housing.

Regulations: Produced according to applicable EN60598-1 CEI 34-21 standards, IP657 degree of protection according to EN 60529 standards. This product has obtained the ENEC European certification of conformity and can be installed on normally inflammable surfaces.

Wind surface: 300 sqcm

Microsoft Windows XP SP2
Intertraff Parking Manager

© 2006 Intertraff All rights reserved.

Reproduction in whole or in part without permission is prohibited.
Features and specifications are subject to change without notice.
All weights and measures are approximate.